Kalkulator Injap Cv/Kv

Injap Cv / Kalkulator Kv

Calculate the required valve flow coefficient for liquid applications using flow rate, penurunan tekanan, dan graviti tentu.

Kadar Aliran Cecair (Q)

Aliran cecair isipadu yang diperlukan.

Graviti Tertentu (SG)

Relative to water at the relevant reference condition.

Tekanan Masuk (P1)

Tekanan tolok hulu.

Tekanan Keluaran (P2)

bar

Tekanan tolok hiliran.

Permohonan: Preliminary calculation for single-phase, non-choked turbulent liquid flow. Tidak sesuai untuk gas, wap, aliran berkelip atau berongga.

Keputusan Pengiraan

Diperlukan Kv (Metrik)

—

m³/j pada 1 bar pressure drop for water

Diperlukan Cv (AS)

—

GPM AS di 1 psi pressure drop for water

Penurunan Tekanan: —

Kadar Aliran Dinormalisasi: —

Graviti Tertentu: —

Notis Kejuruteraan: This result represents the preliminary required flow coefficient. Final sizing must use manufacturer valve performance data and evaluate fluid properties, operating conditions and possible choked flow.

Perlukan Bantuan Memilih Injap Perindustrian?

Share your calculated flow coefficient and operating parameters with Farpro Valve for technical product review.

Minta Sokongan Pemilihan Injap →

Apa Itu Injap Cv / Kalkulator Kv?

A valve Cv/Kv calculator estimates the required flow coefficient for a specified liquid flow rate and differential pressure. Engineers use flow coefficients to compare valve flow capacities and support preliminary valve selection.

Formula Pengiraan Injap Cv dan Kv

Kv = Q × √(SG / ΔP)

Q ialah kadar aliran cecair dalam m³/j. SG ialah graviti tentu cecair. ΔP ialah tekanan pembezaan dalam bar. This simplified relationship applies to non-choked turbulent liquid flow.

Cv ≈ 1.1561 × Kv

Cv lwn. Kv: Perbezaan Utama

Parameter	Cv	Kv
Sistem pengukuran	kebiasaan AS	Metrik
Unit aliran rujukan	GPM AS	m³/j
Rujukan penurunan tekanan	1 psi	1 bar
Penukaran	Cv ≈ 1.1561 Kv	Kv ≈ Cv / 1.1561

Contoh Pengiraan Injap Cv

Consider a water system with a liquid flow rate of 10 m³/j, tekanan masuk sebanyak 5 bar(g), dan tekanan keluar sebanyak 4 bar(g). Dengan graviti tentu 1.0, penurunan tekanan ialah 1 bar. Kv yang diperlukan yang terhasil ialah 10.0 dan Cv adalah lebih kurang 11.56.

Cara Memilih Injap Menggunakan Cv atau Kv

Compare the required coefficient with the manufacturer's published valve capacity data at the intended operating position. Two valves with the same nominal diameter may have different flow coefficients.

Pertimbangkan penarafan tekanan injap, badan dan bahan pengedap, suhu proses, sifat bendalir, ciri injap dan pemulihan tekanan. Final valve sizing may require calculations according to IEC 60534-2-1.

Soalan Lazim

Bolehkah Cv menentukan diameter injap secara langsung?

Tidak. Cv indicates flow capacity under specified reference conditions. The required valve size depends on the manufacturer's valve design and its available flow coefficients.

Adakah Cv yang lebih tinggi sentiasa lebih baik?

Tidak. Oversized control valves can provide poor regulation at low openings. A suitable valve must meet the required operating range.

Bolehkah injap wap saiz kalkulator ini?

Tidak. Steam and gas are compressible fluids and require separate sizing equations and additional process data.

Adakah alat ini memeriksa peronggaan?

Tidak. This calculator does not evaluate cavitation, berkelip, aliran tercekik atau pembetulan kelikatan.

Terokai Injap Perindustrian Farpro

Terokai Farpro injap glob , injap bola dan injap rama-rama untuk aplikasi paip industri.

Penafian: Calculation results are preliminary estimates and do not replace detailed engineering design, manufacturer valve sizing data, atau semakan yang layak.